CANivore USB Male C to Male C Cable

1 Meter USB Type C Male to Type C Male Cable - White

CAN Bus & Power Cable Kit

The CAN Bus & Power cable set includes the following twisted cables: Cable Colors AWG Cable Length End 1 End 2 Red & Black 22 & 22 12" ~3/8" Stripped & Tinned Leads ~3/8" Stripped & Tinned Leads Yellow & Green 22 &...

120 Ohm Resistors (25-Pack)

These 120 Ohm resistors are intended to be used with your CAN Bus systems as terminating resistors. Proper CAN buses, such as vehicle or industrial buses, have 120 Ohm termination resistors at the two ends of the bus harnesses.  CTR Electronics...

3-Pin Addressable LED Cables

Pair of Male/Female 3-pin addressable LED cables This is the standard connectorization for addressable LED strips  Wire a female cable to the CANdle to easily connect and disconnect from CTR Electronic's LED strips. Please see the table below for...

USB Type C Wire Breakout

0.3 (1ft) Meter USB Type C Male to Exposed Power Wires Can be used with the CANdle to power USB Type-C devices with 5V Red Wire +USB (5V), 22AWG Black Wire -USB (0V), 22AWG

USB Micro Power Wire Breakout

0.3 (1ft) Meter USB Micro Male to Exposed Power Wires Can be used with the CANdle to power USB Type-C devices with 5V Red Wire +USB (5V), 22AWG Black Wire -USB (0V), 22AWG

Silicone Wire - 12 AWG

The perfect wire for wiring robots cleanly and effectively. This is a flexible 12 AWG stranded wire utilizing a silicone based insulation making it ideally suited for power distribution in a robot. Use it with motor controllers such as the Victor SP,...

Anderson Powerpole Contact

This is an Anderson Powerpole Contact to be used in conjunction with the Anderson Powerpole Housings (PP15/45 series). The housings are sold separately. Purchase the exact number you need here (max 100 per order).  

Anderson Powerpole PP15/45

This is an Anderson Powerpole Housing. This connector solution makes wire-wire and wire-board electrical connections clean and robust. This housing can be used with a 15 A contact, 30 A contact, or a 45 A contact. The contacts are sold separately. All of...

Limit Switch Wire Assembly

A 4-pin JST cable interfaces with the Talon FX to connect forward and reverse limit switches signals to the controller.This product includes a 4-pin JST connector with differently colored, pre-crimped wires inserted into the connector. The other ends of...

CAN Bus Cable

This is twisted pair of 22 AWG yellow and green wire. This cable is designed to be used as a CAN Bus cable. Can be purchased in a custom length of continuous cable under 99 feet or as spools in fixed lengths. Specifications: Conductors per cable:...

Data Cable Extender (5 Pack)

A simple cable extender module. Connect two data cables (PN 14-886867) together for increased length for either the Talon SRX or the Hero Development Board. Connect two data cables (PN 14-886867) together for increased length.

Battery Beak - Tamiya to SB-50A Cable

Product Overview: This is a Tamiya to Anderson SP-50A power cable. Use this connector with the Battery Beak when needing to check and test batteries for the VEX Robotics and FTC competitions. No more guessing if your batteries are fully charged. Go...

Twisted Power Wire

This is twisted pair of 22 AWG red and black wire. This cable is designed to be used for powering low-current devices Can be purchased in a custom length of continuous cable under 99 feet or as spools in fixed lengths.Specifications: Length: 10 feet or...

Gadgeteer Breakout Module (5 Pack)

This module breaks-out the Gadgeteer socket pins on a 0.1" header placement. This is excellent for wiring circuits in or out of a main-board and also for wiring Gadgeteer modules with non-Gadgeteer systems. This is a set of 5 Breakout Modules.

Anderson Powerpole Crimper by IWISS

This is a ratcheting crimping tool for Anderson Powerpole Contacts - 15 A (1332), 30 A (1331), and the 45 A (261G2). This tool is manufactured by IWISS. This crimper has a built in contact positioner that holds the contact during crimping. There are 3...

CAN Connector (5 Pack)

The CAN Connector makes joining together two CAN devices easy.The CAN Connector joins together two CAN devices. For devices that support a CAN bus (such as the Talon SRX), the CAN Connector can be used to "daisy chain" multiple devices together. See...

Battery Cable

FRC READY Battery Cable made with INFINITIFLEX 6 AWG wire - extremely DURABLE while also being extremely FLEXIBLE.Product Overview: This FRC READY Battery Cable is made with INFINITIFLEX 6 AWG wire which is extremely durable while also being EXTREMELY...

Power Distribution Panel WAGO Tool

WAGO Operating Tool for easily opening the red and black WAGO connectors on the PDP.Product Overview: This WAGO Operating Tool is perfect for easily opening the WAGO connector on a Power Distribution Panel for wire insertion and release. Using this tool...

Talon SRX Encoder Breakout Board

This breakout board makes wiring a quadrature encoder or a limit switch to the Talon SRX quick and easy. When connected to the Talon SRX through a ribbon cable , the breakout board provides solder pads for quadrature encoders (on the top) and limit...